Top Tips to install penny floor and copper penny tile floor

Penny floors of copper pennies, how to install penny floor or make penny floor and penny flooring from penny round tile of copper pennies or coins and cents, penny tiled floor, penny tile floor, copper tiles with stylish designs and ideas

penny floor tile from copper pennies and coins

You want to put a new floor? Then you have to get acquainted with the penny floor, penny tile floor or copper penny floor. It is very fashionable and is done by hand, but it looks like a breathtaking luxury floor, cozy and quiet. Learn how to make your own floor of copper pennies.

Applying a penny floor creates an interesting look in the room. You can choose a bright, shiny new tin penny, a penny with the patina of age, or a combination, depending on your tastes.

Another option for copper penny tile floor is the head or tail up randomly, and others. Penny design floor depends entirely on personal choice. Installing penny floors is very time-consuming. Does that spark an idea?

I think that you will like :
Full catalog of 3D Flooring murals

penny floor tile designs from copper pennies

Tips on how to make a penny floor :

It may sound cheap but received just fine, subtle and difficult. This is a relatively simple operation, and the result will surprise you.

penny floor,copper penny floor tile installation

penny floor and copper penny floor tile installation

You can see also :
How to paint concrete floors in detailed steps

Step by step to install penny floor coins penny tile :

Remove all the doors and base moldings of the room.

Repair any defects based on sex. Grind high spots with medium sandpaper. Use a drill with a wire brush a little on the brick surfaces. Fill holes and depressions on the black floor. Use joint compound on wood substrates and hydraulic cement on the concrete floors.

Clean the floor with a mild degreasing detergent to remove dirt and oil. Rinse the floor thoroughly and let it dry completely.

penny floor and copper penny floor tile installation

Cut squares of self-adhesive fiberglass mesh in the same size. Cut the squares with scissors or a knife. Sizes range from 6 to 6 inches to 12 by 12 inches, depending on your choice. Use a metal straight edge as a guide to ensure straight lines on the squares. Measure room for determining the area and create enough squares to cover the basis of sex.

pace fiberglass mesh squares with the adhesive side up. Apply a pittance square, line by line. The line penny tile to a straight line on the edge of the area. Put every penny as it relates to the next. Continue to apply a penny to penny do not cover all of your squares.

Measure the length of the wall on both sides of the room. Mark the floor at each end. The expansion of the chalk line between the two points and snap a chalk line. Move to the center of the room a distance equal to the size of the square mesh, measure both ends, and snap a chalk line. Repeat until the chalk line covers the floor at intervals equal to the size of your squares.

penny floor, copper penny tile floor

Measure the width of the room from both sides, mark the floor, extend the chalk line, and snap. Move a distance equal to a grid of squares, mark the floor, and snap a chalk line. Continue to measure, mark, and snap a chalk line until the grid does not cover the entire floor.

penny floor, copper penny tile floor

Apply a thin layer of epoxy resin floor adhesive inside the square with a brush. Start at the center of the room. Install a penny tile floor in place and push it by hand to ensure good adhesion. Move to the left or right, apply glue to the floor, set the tile, and press place. Continue until penny tile flooring. made the cut tile with a knife or scissors as needed around a penny. Do not cut a penny. Hide gaps in the base molding.

Allow the glue to dry for four to six hours.

penny floor, copper penny tile floor

Mix the solution with water in a large bucket or trough. Apply grout to the penny tile floor with a float rubber solution. Wipe the excess grout from the surface of the copper penny with a damp sponge.

Allow the plaster for 48 to 72 hours.

Mix the two-component epoxy clear sealer manufacturer's instructions. Select the epoxy sealant that UV filters to prevent yellowing. Pour the sealant onto the floor creating a 1-inch coating. Spread evenly sealant with a long-handled rubber spatula. Allow the epoxy sealant to be collected for 48 to 72 hours before use.